Haan Carpet Cleaner SI 35 User Manual

Slim & Light  
Floor  
Sanitizer  
Si-35  
The Fastest, Easiest  
and Most Effective Way  
to Clean and Sanitize  
Your Floor!  
User Manual  
 
Introduction  
You’ll never use a bucket and mop to clean your floors again!  
Congratulations on purchasing the HAAN Slim &  
Light Floor Sanitizer. Now you have an easy way to  
clean your tile, hardwood, laminate, linoleum and  
vinyl floors.  
Your floor sanitizer uses steam to remove tough  
grease, dirt and grime. Steam is nature’s purest and  
most powerful cleaner for safely cleaning all hard  
surfaces in your home without harsh chemicals, for  
a perfectly ecological approach. No film, no residue  
– just clean, germ-free floors.  
The HAAN Slim & Light Floor Sanitizer is so easy  
to assemble, you can put it to use right away –  
anywhere you want to clean and sanitize – from your  
kitchen and living room to your bathroom floors.  
Look for the HAAN “steamlet” symbol in this manual  
for Helpful HAAN Hints that will help you make the  
most of your new HAAN Slim & Light Floor Sanitizer.  
Backed with a one-year limited warranty, your quality  
HAAN Slim & Light Floor Sanitizer is sure to give  
you years of dependability. And our Customer Care  
representatives are available to answer any of your  
questions about your new floor sanitizer.  
Thousands of HAAN customers have already fallen  
in love with the HAAN Slim & Light Floor Sanitizer.  
We’re confident you will, too.  
Thank you again for purchasing the HAAN Slim &  
Light Floor Sanitizer.  
The HAAN Team  
877-HAAN DIRECT / 877-422-6347  
pg 1  
 
Important Safety Information  
For HoUSeHolD USe onlY  
Basic precautions should be observed when using an  
electrical appliance, including the following:  
iMPortant  
1. Do not direct steam at people, animals, or at electrical  
outlets.  
i
Be sure to read ALL  
instructions and warnings  
before using your HAAN  
Floor Sanitizer.  
2. Do not expose to rain.  
3. Store indoors.  
4. Unplug from outlet when not in use and before  
conducting maintenance or troubleshooting.  
5. Do not leave steam cleaner unattended.  
Warning  
6. Do not leave the steam cleaner connected to an  
electrical outlet when not in use.  
Risk of electrical shock -  
be sure to read and follow  
all instructions and  
warnings.  
7. Do not service steam cleaner when it is plugged in.  
8. Do not use with damaged cord or plug.  
9. Do not use steam cleaner if it has been dropped,  
damaged, left outdoors or dropped into water. Return  
to a service center.  
CaUtion  
!
10. Do not handle steam cleaner with wet hands.  
The SI-35 emits steam at  
212˚F to sanitize the area  
of use. This means that the  
steam head, Ultra-Microfiber  
Pads and Gliding Attachment  
get very hot during use.  
Care should be taken when  
using this appliance and  
DO NOT touch them during  
use except in the approved  
manner as outlined in this  
manual.  
11. Do not pull or carry by cord, use cord as a handle,  
close door on cord, pull cord around sharp corners or  
expose cord to heated surfaces.  
12. Do not unplug by pulling on cord.  
13. Do not use appliance in an enclosed space filled with  
vapor given off by oil-base paint thinner, some  
moth-proofing substances, flammable dust, or other  
explosive or toxic vapors.  
14. Do not allow to be used as a toy.  
15. Do not use on leather, wax polished furniture or  
floors, synthetic fabrics, velvet or other delicate,  
steam-sensitive materials.  
SAVE THESE  
INSTRUCTIONS -  
For household use only.  
Any other use of this  
appliance will void the  
manufacturer’s warranty.  
16. Do not immerse.  
17. Do not use for any purpose other than described in  
this User Manual.  
18. Use only manufacturer’s recommended attachments  
– use of attachments not provided or sold by HAAN  
pg 2  
877-HAAN DIRECT / 877-422-6347  
 
may cause fire, electric shock or injury.  
19. Never put descaling, aromatic, alcoholic or detergent  
products into the steam cleaner, as this may damage  
it or make it unsafe for use.  
20. Unplug by grasping the plug, not the cord.  
21. Close attention is necessary when used by or  
near children.  
22. If the circuit breaker activates while using the steam  
function, discontinue product use immediately and  
contact the customer support center. (Beware of the  
risk of electrical shock.)  
23. Do not allow the product to be disassembled and/  
or modified by anyone other than an authorized  
service technician. (Doing so can result in fire and/  
or electrical shock.)  
grounding instructions:  
iMPortant  
The HAAN SI-35 must be connected to a grounded (3-prong)  
wiring system. Grounding provides a safe path of least  
resistance for electrical current, in the event the unit should  
malfunction or break down, thereby reducing the risk of  
electrical shock. The cord for this product has an equipment-  
grounding conductor and a grounding plug. Do not plug it into  
an outlet that is not properly installed and grounded in  
accordance with all local codes and ordinances.  
Grounded  
Pin  
Grounded  
Outlet  
Warning  
Check with a qualified electrician or service person if you  
aren’t sure if the outlet is properly grounded. If it will not  
fit the outlet, have a proper outlet installed by a qualified  
electrician. This appliance is designed for use on a nominal  
120-volt circuit and has a grounding attachment plug as  
illustrated above. Make certain that the appliance is connected  
to an outlet having the same configuration as the plug. No  
plug adapter should be used with this appliance.  
DO NOT modify the plug.  
Improper connection of  
the equipment-grounding  
conductor can result in a  
risk of electrical shock.  
877-HAAN DIRECT / 877-422-6347  
pg 3  
 
Product Description  
1
2
Si-35  
Slim & Light  
Floor  
Sanitizer  
4
3
5
6
7
8
9
10  
11  
Included Accessories:  
Ultra-Microfiber  
Pads (2)  
Gliding Tray (1)  
13  
Floor Protector/  
12  
Resting Mat (1)  
pg 4  
877-HAAN DIRECT / 877-422-6347  
 
FeATUReS:  
1. Handle -  
with non-slip ergonomic grip to reduce hand & wrist stress.  
2. Storage Hook -  
Rotates 360˚ so it can be used to manage the cord and then  
provide convenient, easy hanging storage.  
HELPFUL HAAN HINT:  
15 Powerful Steam Jets  
are spaced perfectly to  
cover more floor in less  
time. Be assured you are  
steam cleaning when  
you push the machine  
forward, as well as when  
you are pulling it back.  
3. Pivoting Power Cord Wrap-  
releases cord with a flick of the wrist.  
4. Power Cord Management System -  
keeps your pathway clear  
5. Power Cord with Flexible Cord Support -  
double insulated cord with a 3-prong plug complete with  
a flexible cord support strengthens cord connection.  
6. Removable Water Tank -  
goes to the sink for easy filling and allows for 20 minutes  
of continuous steam on just one tank.  
7. Water Tank Release Button  
HELPFUL HAAN HINT:  
To extend the life of your  
Ultra-microfiber pads,  
always place your unit on  
the floor protector/resting  
pad while the unit heats  
up, and attach the Ultra-  
Microfiber pad when the  
unit is ready to use.  
8. Indicator Light -  
turns red when unit is ON.  
9. ON/OFF Switch -  
Steam Power Switch for easy ON/OFF operation.  
10. Steam Head -  
gets around and under difficult areas.  
11. Ultra-Microfiber Pad - (2)  
patented super-absorbent Ultra-Microfiber Pads lock in dirt  
and leave floors dry to the touch. Specially designed for  
‘No-Touch’ attachment and removal.  
Make sure to check for the following accessories!  
HELPFUL HAAN HINT:  
While using the Floor  
12. Floor Protector/Resting Mat -  
for use when heating up your floor sanitizer or when  
taking a break from active cleaning.  
Sanitizer with the Gliding  
Tray will not lift all set-in  
stains from your carpet, our  
patented Ultra-Microfiber  
pad may be used to act as a  
“blotter” for removing most  
fresh, wet spills and stains.  
13. Gliding Tray -  
easily attaches to unit for sanitizing and refreshing  
carpeted areas.  
877-HAAN DIRECT / 877-422-6347  
pg 5  
 
Assembling Your Floor Sanitizer  
1 2 Ready to Go  
To enable you to get the most satisfaction  
from your Floor Sanitizer be sure to follow  
the assembly and operating instructions  
included in this manual. Read this manual  
thoroughly before assembling your unit.  
Locking  
Pin  
Pay specific attention to the product  
description to familiarize yourself with all  
the parts of your Floor Sanitzer. Locate  
and organize the parts of the unit before  
assembling. No additional tools are needed  
to put the unit together. It is quick and easy.  
1 Look for the small red  
“HANDLE” arrow on the  
aluminum pipe; align the  
black pistol-grip handle  
with the locking pin; hold  
the pin down; insert the  
pole and snap it into place.  
Locking  
Pin  
Align the lower shaft  
2
(where you’ll find the  
white hook) with the  
locking pin on the  
side and snap it  
into place.  
Storage Hook  
Rotates 360˚  
pg 6  
877-HAAN DIRECT / 877-422-6347  
 
Before Using Your Floor Sanitizer  
Be sure to read ALL instructions and warnings  
before using your HAAN Floor Sanitizer.  
i
Warning  
!
HELPFUL HAAN HINT:  
Your floor sanitizer is designed to clean hard floor surfaces  
that will withstand high heat. Do not use on unsealed wood  
or unglazed ceramic floors. On surfaces that have been treated  
with wax or some no-wax floors, the sheen may be removed  
by the heat and steam action. It is always recommended to  
test an isolated area of the surface to be cleaned before  
proceeding. We also recommend that you check the use and  
care instructions from the floor manufacturer.  
Never leave the appliance in  
one spot on any surface for  
any period of time. Always  
place your Floor Sanitizer on  
the Floor Protector/Resting  
Mat when stationary and  
make sure the floor sanitizer  
is turned off not in use.  
CaUtion  
Use a grounded receptacle. Use only a heavy duty extension  
cord rated for 15 amps minimum – DO NOT use an ordinary  
extension cord. To provide continued protection against the  
risk of electric shock, connect to properly grounded outlet only.  
HELPFUL HAAN HINT:  
DO NOT add cleaning  
solutions, scented perfumes,  
oils or any other chemicals  
to the water used in this  
appliance. Use regular tap  
water, or if the tap water in  
your area is very hard, we  
recommend you use  
iMPortant  
This product is NOT for space heating purposes.  
iMPortant  
Always be sure that your floor sanitizer is UNPLUGGED from  
the wall receptacle prior to filling the water tank.  
distilled/purified water.  
Always empty water from  
water tank after use.  
CaUtion  
!
The SI-35 emits steam at 212˚F to sanitize the area of use.  
This means that the steam head, Ultra-Microfiber Pads  
and Gliding Attachment get very hot during use. Care  
should be taken when using this appliance and DO NOT  
touch them during use except in the approved manner as  
outlined in this manual.  
877-HAAN DIRECT / 877-422-6347  
pg 7  
 
Using Your Floor Sanitizer  
Fig 1a  
Operating Instructions:  
1) Remove all parts from the packaging.  
2) Assemble the unit as described on page 6.  
3) Place the Floor Sanitizer on the Floor Protector/  
Resting Mat and remove the water tank by  
Fig 1b  
Fig 2  
pressing the water tank removal button. (Fig 1a)  
4) Grasp the water tank, pull out and up to remove.  
(Fig 1b)  
5) Turn the cap on the water tank counter-clockwise  
to open it and fill the tank with water. (Fig 2)  
6) After filling the water tank with water, firmly  
turn the cap clockwise to close. Insert the tank,  
cap down, into the receptacle in the main unit  
and push forward until it clicks into place. (Fig 3)  
Fig 3  
7) Press the STEAM ON/OFF button found on the  
front of the unit. It takes approximately 30  
seconds for the floor sanitizer to heat up.  
8) Place an Ultra-Microfiber pad on the floor with  
the ‘hook & loop’ side facing up.  
9) Raise the unit off the Floor Protector/Resting Mat  
and lightly press it down onto the Ultra-Microfiber  
pad. You are now ready to steam clean and sanitize  
your floor. (Fig 4)  
Fig 4  
10) Push and pull the floor sanitizer slowly across  
the floor to thoroughly steam clean each section.  
11) When there is no more water in the water tank,  
you will hear a vibration sound from the main  
unit. To refill the water tank and continue to  
sanitize, turn your floor sanitizer off. Unplug the  
unit from the electrical wall outlet and remove  
the water tank and refill the water tank as before.  
HELPFUL HAAN HINT:  
Never leave the appliance in one  
spot on any surface for any period  
of time. Always place your Floor  
Sanitizer on the Floor Protector/  
Resting Mat when stationary and  
make sure the floor sanitizer is  
turned off not in use.  
12) When you have finished using the Floor Sanitizer,  
turn it ‘OFF’, place it on the Floor Protector/  
Resting Mat and wait until the Floor Sanitizer  
cools down for approximately five (5) minutes  
pg 8  
877-HAAN DIRECT / 877-422-6347  
 
Operating Instructions: (cont)  
before removing the ultra-microfiber pad from the base.  
NOTE: The ultra-microfiber pad gets very hot  
with the steam. Allow it to cool before removal.  
HELPFUL HAAN HINT:  
After heating up, it is normal  
to hear a vibration sound  
from the water pump inside  
the main unit. It will stop  
when the air inside has been  
pumped out. If the vibration  
sound goes on for more  
than 60 seconds, check to  
be sure the water tank is  
assembled correctly.  
13) Store the unit upright in a protected dry area,  
standing it on the Floor Protector/Resting Mat,  
or by hanging it by the Storage Hook.  
Special Notes on Using your HAAN Floor Sanitizer:  
Always vacuum or sweep floor before sanitizing.  
The easiest way to use the machine is to tilt the  
handle to a 45˚ angle and clean slowly 2-3 yards  
at a time.  
HELPFUL HAAN HINT:  
We recommend placing your  
floor sanitizer on the Floor  
Protector/Resting Pad while  
the unit heats up. When the  
unit is ready, lift it off of the  
resting pad and simply place  
the Ultra-Microfiber pad on  
the floor. The ‘hook & loop’  
system quickly attaches the  
pad to the base of the unit.  
Never push or pull the floor  
sanitizer across your floor  
without the Ultra-Microfiber  
pad attached to the base.  
Although we do not advocate the use of chemicals,  
to remove stubborn stains from vinyl or linoleum  
floors, you can pre-treat with a mild detergent  
and some water before using the floor sanitizer.  
Ultra-Microfiber Pads  
What is an ultra-microfiber?  
An ultra-microfiber is a textile fiber that is thinner  
than a microfiber. The Ultra-Microfiber by HAAN  
Corporation is 5-10 times thinner than common  
microfiber providing for a significantly higher thread  
count in the same surface area. The thinner and  
higher the thread count, the greater the absorbtion.  
HAAN’s Ultra-Microfibers are so thin that more dirt  
and dust gets trapped between the fibers, making  
your cleaning simpler and less time-consuming.  
HELPFUL HAAN HINT:  
Never leave the Ultra-  
Microfiber pad on your  
floor sanitizer when you  
have finished using the  
floor sanitizer.  
877-HAAN DIRECT / 877-422-6347  
pg 9  
 
Operating Instructions: (cont)  
How to Use Ultra-Microfiber Pads:  
Fig 5  
Fig 6  
Fig 7  
1) Please make sure that you always use completely  
dried pads.  
2) The Ultra-Microfber pad is made up of multiple  
layers of super absorbent material. (Fig 5) The  
outer layer is Ultra-Microfiber on one side and  
a ‘hook & loop’ system on the other side that  
attaches easily to the underside of the steam  
head. Simply place the pad on the floor with the  
‘hook & loop’ side up, and lightly press the SI-35  
Floor Sanitizer down on the pad.  
(refer back to Fig 4)  
3) As high temperature steam passes through a pad  
to contact the floor to kill germs, molds and mites,  
it is natural that the pad gradually absorbs moisture.  
After a certain length of time, the pad repels  
water and becomes damp. When the pad becomes  
saturated, turn the unit ‘OFF’ and wait until the  
Floor Sanitizer cools down for approximately five  
(5) minutes.Put your foot on a corner of the pad  
and lift the Floor Sanitizer off the pad. (Fig 6)  
Replace with a dry pad on the unit, turn the unit  
back on and continue.  
4) To keep the floor clean and dry, replace the pad  
when it is dirty and/or saturated.  
Warning  
!
Colors may bleed during  
first wash. Be careful when  
machine washing or drying  
with mixed fabrics as  
How to Clean and Store the HAAN  
Ultra-Microfiber Pads:  
1) Ultra-microfiber pads are easy to wash. Soak pads  
for about 1-2 hours in cold or lukewarm water  
with laundry detergent and hand wash them.You  
can also drop the pads in a washing machine and  
clean them using the gentle/delicate cycle. DO  
NOT use fabric softener as this will compromise  
the absorbancy of the microfiber. (Fig 7)  
micro-fiber cloths will pick  
up lint from other fabrics.  
HELPFUL HAAN HINT:  
You may dry your Ultra-  
Microfiber pads in a machine  
dryer on a low setting, but for  
longer life, we recommend air  
drying the pads.  
2) It is best to let the pads air dry but you can  
place them in the dryer using low heat.  
pg10  
877-HAAN DIRECT / 877-422-6347  
 
Operating Instructions: (cont)  
glide attachment  
What is the Glide Attachment?  
The Glide Attachment enables the Floor Sanitizer to  
freshen, deodorize and sanitize carpeting, rugs,  
upholstery, pet cushions and more. Used with the  
Floor Sanitizer it kills dust mites and other allergans  
in a variety of soft surfaces.  
Fig 8  
Fig 9  
Fig 10  
How to use the Glide Attachment:  
1) The Glide Attachment is used without the Ultra-  
Microfiber pad. It attaches directly to the unit by  
snapping onto the bottom of the steam head.  
Place the front of the steam head under the tabs  
on the front of the Glide Attachment and press  
down. The tray is made to fit snuggly and will  
snap easily into place. (Fig 8)  
2) After attaching the tray, press the ‘STEAM ON/  
OFF’ button found on the front of the unit. It  
takes approximately 30 seconds for the Floor  
Sanitizer to heat up.  
3) Push and pull the Floor Sanitizer slowly across  
the carpet (or other soft surface) to thoroughly  
steam clean each section. (Fig 9)  
4) When there is no more water in the water tank,  
you will hear a vibration sound from the main  
unit. To refill the water tank and continue to  
sanitize, turn your floor sanitizer off. Unplug the  
unit from the electrical wall outlet and remove  
the water tank and refill the water tank as before.  
5) When you have finished using the Floor Sanitizer,  
turn it ‘OFF’, place it on the Floor Protector/  
Resting Mat and wait until the Floor Sanitizer  
cools down for approximately five (5) minutes.  
Remove the Glide Attachment by using your foot  
to snap the attachment off the steam head. The  
attachment is designed for this ‘No Touch’  
method of removal. (Fig 10)  
HELPFUL HAAN HINT:  
Never leave the appliance in  
one spot on any surface for  
any period of time. Always  
place your Floor Sanitizer on  
the Floor Protector/Resting  
Mat when stationary and  
make sure the floor sanitizer  
is turned off not in use.  
6) Store the unit upright in a protected dry area,  
standing it on the Floor Protector/Resting Mat,  
or by hanging it by the Storage Hook.  
877-HAAN DIRECT / 877-422-6347  
pg 11  
 
Operating Instructions: (cont)  
CaUtion  
How to use the Glide Attachment for Fresh Stains:  
!
The SI-35 emits steam at  
212˚F to sanitize the area  
of use. This means that the  
steam head, Ultra-Microfiber  
Pads and Gliding Attachment  
get very hot during use.  
Care should be taken when  
using this appliance and  
DO NOT touch them during  
use except in the approved  
manner as outlined in this  
manual.  
The Glide Attachment can be used to break up fresh  
stains on carpeting, rugs, upholstery, pet cushions  
and other soft surfaces. Follow the instructions below.  
1) With the Glide Attachent on the Floor Sanitizer,  
press the ‘STEAM ON/OFF’ button. It takes  
approximately 30 seconds for the Floor Sanitizer  
to heat up.  
2) Place the Floor Sanitizer over the stain and hold it  
in place for a few seconds to allow the steam to  
penetrate the area of the stain.  
3) Push and pull the floor sanitizer slowly across  
the area to work the steam into the stain.  
Fig 11  
4) Carefully remove the Glide Attachment by using  
your foot to snap the attachment off the steam  
head. The attachment is designed for this easy  
‘No Touch’ method of removal. (Fig 11)  
5) Place a dry Ultra-Microfiber Pad ‘hook & loop’  
side up and press the unit onto the pad. Use the  
pad to rub the area, simultanously working at the  
stain and blotting the moisture from the surface.  
6) When you have finished using the unit, turn it ‘OFF’,  
place it on the Floor Protector/Resting Mat and  
wait until the Floor Sanitizer cools down for  
approximately five (5) minutes before removing  
the Ultra-Microfiber Pad from the base.  
HELPFUL HAAN HINT:  
While using the Floor  
Sanitizer with the Gliding Tray  
will not lift all set-in stains  
from your carpet, our patented  
Ultra-Microfiber pad may be  
used to act as a “blotter” for  
removing most fresh, wet  
spills and stains.  
7) Store the SI-35 upright in a protected dry area,  
standing it on the Floor Protector/Resting Mat,  
or by hanging it by the Storage Hook.  
pg 12  
877-HAAN DIRECT / 877-422-6347  
 
Care & Maintenance  
1) Turn your Floor Sanitizer off and unplug the unit  
from the electrical outlet.  
iMPortant  
2) Place the unit on the Floor Protector/Resting Mat.  
Always be sure that your floor  
sanitizer is UNPLUGGED from  
the wall receptacle prior to  
cleaning or before emptying  
the water tank.  
3) Prepare to store the Floor Sanitizer by looping the  
power cord around the pivoting cord wraps found  
on the handle pole and snap the plug securely  
onto the cord when complete.  
4) Let your Floor Sanitizer cool for five (5) minutes  
before removing the Ultra-Microfiber pad.  
5) Always empty the water tank once you have  
finished using your Floor Sanitizer.  
HELPFUL HAAN HINT:  
Never leave the appliance in  
one spot on any surface for any  
period of time. Always place  
your Floor Sanitizer on the Floor  
Protector/Resting Mat when  
stationary and make sure the  
floor sanitizer is turned off not  
in use.  
6) Remove the Ultra-Microfiber pad and wash in  
warm water with a mild detergent. Never use  
bleach or fabric softener when cleaning the Ultra-  
Microfiber pad. The Ultra-microfiber pad can be  
washed in a washing machine set on the gentle  
cycle. We recommend that you air dry the pads  
for 24 hours, but they can also be dried in a  
clothes dryer on a low heat setting.  
7) To clean the body of your Floor Sanitizer wipe it  
down with a damp cloth.  
CaUtion  
8) Store the unit upright in a protected dry area,  
standing it on the Floor Protector/Resting Mat,  
or by hanging it by the Storage Hook.  
Do not immerse your Floor  
Sanitizer in water or any  
other liquid.  
HELPFUL HAAN HINT:  
DO NOT use fabric softener  
when washing the Ultra-  
Microfiber Pads as this will  
compromise the absorbancy  
of the microfiber.  
877-HAAN DIRECT / 877-422-6347  
pg 13  
 
Troubleshooting and Questions  
This chapter summarizes the most common problems you  
could encounter with your floor sanitizer. Please read the  
different sections for more details. If you are unable to  
solve the problem, please contact our Customer Care  
Representatives at 877-HAAN DIRECT (877-422-6347)  
PROBLEM: Floor Sanitizer vibration sound last longer  
than 60 seconds.  
Possible Cause:  
1) No water in the water tank.  
2) Water tank is not snapped into place.  
Possible Solution:  
1) Add water to the water tank following  
instruction on page 8.  
2) Insert the water tank properly into the  
main body of the SI-35.  
PROBLEM: Floor Sanitizer does not operate.  
Possible Cause:  
1) Power cord not firmly plugged into outlet.  
2) No power in wall outlet.  
Possible Solution:  
1) Check plug in outlet and set plug firmly.  
2) Check fuse or breaker. Replace fuse and/or  
reset breaker.  
PROBLEM: Floor Sanitizer does not emit steam.  
Possible Cause:  
1) No water in water tank.  
Possible Solution:  
1) Add water to the water tank following the  
instructions on page 8.  
pg 14  
877-HAAN DIRECT / 877-422-6347  
 
PROBLEM: Floor Sanitizer leaves water on the floor.  
Possible Cause:  
1) Ultra-Microfiber cleaning cloth is too wet.  
2) Unit is not level on the floor..  
HELPFUL HAAN HINT:  
For optimal performance,  
the Ultra-Microfiber pad  
should be changed after  
10 minutes of use.  
Possible Solution:  
1) Turn off unit, unplug from power outlet  
and change the Ultra-Microfiber pad.  
2) Always keep the floor sanitizer level and  
parallel to the floor.  
PROBLEM: Floor Sanitizer left a white spot on the floor.  
Possible Cause:  
1) Floor sanitizer left in one spot too long.  
2) Floor sanitizer not rested on floor  
protector pad.  
3) Hard water.  
Possible Solution:  
1) Always place the floor sanitizer on the floor  
protector pad when not in use.  
2) Use distilled water.  
NOTE: To remove spot, use a damp, dry cloth  
with a few drops of white vinegar and rub the  
stain to remove spot.  
QUEStiOn: Can the HAAn floor sanitizer be used on  
laminate flooring?  
?
The HAAN floor sanitizer was designed for use on sensitive  
flooring like laminates. We’ve spent years optimizing the  
steam emission so that at nearly half the wattage of competitive  
products (ours is only 800w versus most that are 1500w),  
we still emit steam at 212˚F. This means our finer vapor-like  
steam is gentler than those that simply blast 1500w of water  
and steam onto your floor. Yet, the HANN is more effective  
at penetrating stains and killing harmful germs and bacteria  
than competitors. Steam is all we do, and we’ve spent years  
perfecting it.  
877-HAAN DIRECT / 877-422-6347  
pg 15  
 
QUEStiOn: the HAAn Floor Sanitizer is leaving my floor  
wet. Why and what can i do about it?  
?
?
The Ultra-Microfiber pad may need to be changed. For  
optimal performance, the pad should be changed after 10  
minutes of use.  
QUEStiOn: How long can you use an Ultra-Microfiber  
Pad before it needs to be changed?  
The pad should be changed every 10 minutes, or when it  
becomes saturated with water. The machine will become  
harder to push smoothly on the floor when the pad is  
saturated.  
QUEStiOn: How long does a tank of water last?  
?
?
A full tank will last approximately 20-25 minutes.  
QUEStiOn: Sometimes my floor sanitizer becomes hard  
to push – why?  
If the unit is hard to push it is likely because the Ultra-  
Microfiber Pad is too wet or the angle at which you are using  
the machine is too high. The lower the handle, the easier the  
floor sanitizer is to push across the floor.  
QUEStiOn: Do i have to use distilled water in my HAAn  
floor sanitizer?  
?
We recommend distilled water, but you may use tap water,  
unless you have hard water in your area. Using hard water  
will shorten the life of your appliance.  
pg 16  
877-HAAN DIRECT / 877-422-6347  
 
QUEStiOn: How do you use the Glide Attachment for my  
carpet?  
?
?
The carpet tray is to be used without the microfiber pad and  
can be attached directly to the unit.  
QUEStiOn: How long can i prolong the life of my HAAn?  
To maintain the life of your floor sanitizer, we recommend  
using HAAN’s Tank Rejuvenator (available on our web site)  
every six months.  
?
?
QUEStiOn: Does the HAAn work on pet stains?  
Yes, the HAAN is able to spot clean fresh pet stains by  
loosening and lifting the stain.  
QUEStiOn: Will the HAAn floor sanitizer clean grout?  
Yes, but it needs a little help. If you glide your HAAN over  
the problem grout areas and then scrub with your microfiber  
pad, it should effectively clean your grout.  
877-HAAN DIRECT / 877-422-6347  
pg 17  
 
Warranty  
One-Year Limited Warranty  
Your HAAN Floor Sanitizer is warranted to be free from  
defects in material and workmanship for a period of one  
(1) year from the date of purchase when utilized for normal  
household use by the original purchaser only. The included  
Warranty Registration Card must be filled out and returned  
within 10 days of purchase. This is essential for your warranty  
to be effective should any problem arise with this product.  
Should any defect covered by the terms of the limited warranty  
be discovered within one year, HAAN Corporation will  
repair or replace the defective part provided the unit is  
returned by the original purchaser, freight prepaid, to:  
HAAN Corporation, 44 North Queen Street, Lancaster, PA 17603  
The liability under this warranty is limited solely to the cost  
of the replacement parts or the complete unit at our option.  
Labor charges are not included.  
This warranty is extended to the original purchaser of the  
unit and excludes all other legal and/or conventional  
warranties. The responsibility of HAAN Corporation, if any,  
is limited to the specific obligations expressly assumed by  
it under the terms of the limited warranty. In no event is  
HAAN Corporation liable for incidental or consequential  
damages of any nature whatsoever. Some states/provinces  
do not permit the exclusion or limitation of incidental or  
consequential damages, so the above may not apply to you.  
This warranty gives you specific legal rights which vary  
from state to state or province to province.  
IMPORTANT: Carefully pack item to avoid damage in shipping.  
Be sure to attach tag to item before packing with your name,  
complete address, and phone number with note giving  
purchase information, model number and what you believe  
is the problem with the item. We recommend you insure the  
package (as damage in shipping is not covered by our  
warranty). Mark the outside of your package ATTENTION  
CUSTOMER SERVICE.” We are constantly striving to improve  
our products; therefore, the specifications contained herein  
are subject to change without notice.  
pg 18  
877-HAAN DIRECT / 877-422-6347  
 
(Fold here and tape closed before mailing)  
 
Place  
Stamp  
Here  
Product Registration  
HAAN Corporation  
44 North Queen Street  
Lancaster, PA 17603  
 

Graco Baby Swing PD162294B User Manual
Graco Baby Walker 4113 User Manual
Harbor Freight Tools Heat Gun 69342 User Manual
Harbor Freight Tools Washer 35740 User Manual
Hasbro Motorized Toy Car 55636 60101 User Manual
Hotpoint Oven RMBA 2200L User Manual
HP Hewlett Packard Photo Printer Z3200ps User Manual
HP Hewlett Packard Welding System 683703 004 User Manual
IBM Computer Hardware CIOv User Manual
IBM Laptop SH19 4480 01 User Manual